#LIFT CONTROL PANEL DESIGN HOW TO#
#LIFT CONTROL PANEL DESIGN OFFLINE#

The controller cabinets are installed usually in the elevator control room above the hoistway. This station should only be operated under the direct supervision of the elevator technician. To be used by the elevator technician when servicing the car. Note: Braille Markings for the COP, Hall Stations and Hall landings are included as standard equipment.Ĭar top operating station provided on some cars for operating the car from the car top.

#LIFT CONTROL PANEL DESIGN HOW TO#

Used to choose the floor that you want to get him.īe Stick on the COP to show how to handle passengers in the car lift in case of emergency. Used in the event of a fire in the elevator.

The car position indicator permits the floor to be read on which the car is located at the moment or displays special information, e.g. Then normal operation can be continued.į- Car position indicator / direction indicator The signal stops automatically as soon as overload is removed. If the car is overloaded, it will remain at the floor with doors open. The overload indicator gives an optical and / or acoustic signal to indicate that the car is overloaded. The fan button switches the fan in the car on / off. The alarm button serves as emergency light which remains active by means of standby-power even in the case of power failure. On operating the alarm button the alarm device will be activated and a voice communication with the emergency service established. On operating the door-open-button the closing movement will be stopped and the door will be re-opened. The door-open-button can be used to open the door or to hold the door open.

Through RS485 stand-alone communication distance of 1200M, one bus supports 127 elevator access control board, each MC-5816 provides two standard card reader interfaces supporting Wiegand 26Bit Wiegand32Bit Wiegand40Bit card reader or fingerprint head as identification device, elevator access control all inputs / Outputs are equipped with dynamic voltage protection, all relay outputs are equipped with instantaneous over-voltage protection, and support fire alarm input linkage.The door-close-button can be used to close the door immediately after a car call is given, which reduces the waiting time. MC-5816A single access controller supports 16 floors management, and can also be extended through expansion boards, it supports 1 expansion board, and finally can manage up to 32 floors, it supports RS485 and TCP/IP networing.

#LIFT CONTROL PANEL DESIGN OFFLINE#

The MC-5816 series elevator access control management system supports offline operation, and can independently store 26,000 groups of personnel data and 100,000 records, so that all personnel entry and exit records on the floor can be found. If you are not authorized by the elevator access control management system, you cannot enter the floors of the management area, and control the time period of important floors. MC-5816 elevator access control board provides different floor access level for different personnel status, you can specify that someone can only go to a certain floor, certain floors or all floors, and manage who can reach a certain floor through the access level, who can not reach a certain floor, and MC-5816 can perform authorization management according to the schedule. The system set up by the addition of all the cardholder to enter the floor, carried out all floors access control. MC-5816 series of smart card elevator access controller can be used to meet building service management company or management personnel access lift more efficient and safer management needs. MC-5816 Is used to lift hierarchical control, personnel up and down the elevator access control systems products. MC-5816 Series of smart card elevator / locker access controller, also known as smart card elevator access control system. Support Card Types: Second-generation identification card, residence permit, Mifare card, CPU card Identification information: Card, Card + Password, Password, double card identification, admin card + user card unlock. Recognition Types: ID card, Mifare Card, Fingerprint, Card, Password Working Mode: Elevator access, lockers access management Networking: Rs485 and TCP/IP >TCP/UIP is optionalĬommunication Distance: 1200m >RS-485 networking Validity Period: Support > One day - 100 years arbitrarily set Working Current: 500mA > Not include card readerĭrive Current: Relay dry contact ( NO, NC software adjustable)

Shell Material: Iron board with plastic spray material Transfer method: Real time, non-real-time Extend: series connection with 1 group can achieve 32 floors control capacity

Lift control panel design